Her kan du finde firmwareopdateringer til dine Logic Group enheder (tidl. Logic Soft og Logic Home Control).

Firmware opdateres via “Over The Air” (OTA) device update. Det er altså ikke nødvendigt at tilslutte enheden til en controller eller PC via kabel da enhedens firmware kan opdateres direkte over det trådløse Z-Wave netværk.

Firmwarefilerne der kan downloades fra denne side har filtypen .OTA. I nogle controllere skal filer være af typen .HEX – i disse tilfælde kan filtypenavnet blot omdøbes, da firmwarefilen allerede er en hexfil.

Kontakt venligst support@logic-group.com hvis du mangler materiale eller har spørgsmål om vores produkter og firmware.

Prøv vores nye Firmware Uploader Common PC applikation til at lave Over-The-Air firmwareopdateringer af alle Logic Groups enheder. Applikationen skal bruge en Z-Wave USB adapter og den ønskede OTA eller OTZ firmwareopdatering, som kan downloades her på siden.

Se vejledningen for instruktioner i brugen af applikationen.

NB. Brug ikke en Z-Wave USB adapter der er i brug af en kørende controller, da firmwareopdateringen da vil resette dit interface!

ZHC5002

Z-Wave kobling for GIRA

Firmware version 2.02:
Med denne opdatering kan LED’er kontrolleres med Z-Wave kommandoer (Command Class Basic Set) ved at sætte konfigurationsparametrene 4-9 (værdi 8).

NB. Efter opdatering af en ZHC5002 enhed til firmware version 2.x fra en version 1.x, er det nødvendigt at udmelde enheden og derefter genindmelde enheden i Z-Wave netværket!
Ældre firmware versioner

Firmware version 2.01:
Supporterer Sikkerhed (S0) for sikker tilføjelse af ZHC5002.
Denne firmware supporterer stadig kommandoer fra ikke-sikre enheder når den konfigureres til at acceptere ikke-sikre kommandoer (se konfigurationsparameter 27 – 32).


Download “ZHC5002 Firmware version 2.01 (OTA)” zhc5002_v2_01_eu.zip – Downloadet 35 gange – 88 KB

ZHC5010

Z-Wave Betjeningstryk

Firmware version 2.03 (ikke Z-Wave Plus certificeret):
Denne firmware version løser problemet hvor VERA controlleren sidder fast i indmeldelsesprocessen med beskeden: “Purging Associations”.

NB. Efter opdatering af en ZHC5010 enhed til firmware version 2.x fra en version 1.x, er det nødvendigt at udmelde enheden og derefter genindmelde enheden i Z-Wave netværket!
Ældre firmware versioner (beskrivelser på engelsk)

Firmware version 2.02 (Not Z-Wave Plus certified):

Includes the following corrections and enhancements (firmware update 2.00-2.02):

  • Correction of a minor bug where Multilevel Switch commands sent from the Controller (or other devices) to ZHC5010 wasn’t sent further to devices in the ZHC5010 device association groups.
  • Supports security (S0) so that ZHC5010 can be added securely.
  • It is also possible to configure that Z-Wave commands sent to devices in each of the ZHC5010 association groups are sent non-secure in order to support non-secure devices (see configuration parameters 33 – 36). This firmware version will function in both secure and non-secure installations.

Download “ZHC5010 Firmware version 2.02 (OTA)” zhc5010_eu_2_02.zip – Downloadet 32 gange – 87 KB

Firmware version 1.12 (not Z-Wave Plus certified):

This firmware version includes the following corrections and enhancements (firmware update 1.10-1.12):

  • Fine-tuning of the button detection timing, see configuration parameters 28 – 32.
  • Possibility of controlling the LED’s by means of standard Basic Set on/off commands, so now all Controllers/Gateways will be able to fully control the LED’s (Configuration parameters 3 – 6, value 8).
  • Correction of an issue in relation to HomeSeer network controllers with older USB network interfaces, that makes it almost impossible to include ZHC5010 into the controller.

Download “ZHC5010 Firmware version 1.12 (OTA)” zhc5010_eu_1_12.zip – Downloadet 31 gange – 80 KB

Firmware version 1.09 (Z-Wave Plus certified):

This firmware version is the newest Z-Wave Plus certified firmware, with following corrections and enhancements (update 1.03-1.09):

  • Corrected: fault in dimmer-command sent to light dimmers could result in that the light was regulated very fast for some dimmer types (especially AEOTEC dimmers), it was practically impossible to regulate the light to a certain level – the fault has been corrected in this firmware version.
  • Improved event handling; it will now ensure that all pending messages will be sent to the devices in the association groups, even when new button activations (or incoming command messages) are made while sending out messages.
  • Improved handling of incoming notifications in order to better serve the proxy mode.
  • New relay modes (see configuration parameter 15 in the user manual).
  • Allow double-press central scene notification, even when the house cleaning mode is disabled.
  • Improved button driver; button double-press is now interpreted as only one event (not first a single-press and then a double press).
  • Corrected fault in that incoming button command messages did not make a correct activation of devices in the Multilevel Switch association groups.
  • Central Scene Command Class is now presented correctly, only in the root device and not in the sub-devices.
  • The sequence number in the Central Scene notification is now updated correctly in order for the controller to detect duplicate scene notifications.
  • Indicator Command Class version 2 is introduced (see further description in the user manual).
  • When configuration parameters for the LEDs are changed, they will now be reflected immediately.

Download “ZHC5010 Firmware version 1.09 (OTA)” zhc5010_eu_1_09.zip – Downloadet 31 gange – 79 KB

ZIF 5028: Interface til Automatik (12-24V)

Z-Wave DIN-skinne ZIF module
Tidligere: LHC5028

Firmware version 0.7:
Med denne opdatering kan indgange kontrollere udgange direkte. Standard konfigurationen vil blive at indgange kontrollerer udgange og at indgangen er “edge triggered”. Det vil sige at hver aktivering af en indgang vil skifte on/off status på indgangen. Med denne default egenskab vil ZIF modulet nu fungere som et kip-relæ.

NB. Når der opdateres firmware i ZIF5028 til version 0.7 vil den miste sin netværksinformation og vil kræve en genindmeldelse i Z-Wave netværket.