Let MATRIX outsmart your old wall switches

… with its backlit pushbuttons, built-in light dimmer or double relay, and one of the most advanced use of Z-Wave technology you have seen so far.

Let MATRIX outsmart your old wall switches

… With its backlit pushbuttons, built-in light dimmer or double relay, and one of the most advanced use of Z-Wave technology you have seen so far.

wifi 4 Z-wave Scene Controllers

Up to 12 possibilies with single-press, double-press and long-press on each of the four buttons.

Multi Functional Backlight

The squares can light up in all colors which can be used to show the status of a lamp, as orientation light during nighttime, visual alarm and much more.

wifi  Z-Wave Plus

Based on the Z-Wave Plus 500 or 700 Series platform.

  Tactile touch

The four switches are designed with luxury and tactility in mind.

Cleaning-friendly

Elegant and cleaning-friendly front. No visible marks from fingerprints.

wifi  Wireless Updates

Firmware can be updated through the Z-Wave network (OTA firmware updates).

Dim all dimmable
light sources with
one product only.
Meet MATRIX ZDB.
The dimmer switch that
fits into CE standards, including
GIRA System 55, Exxact and Elko Plus.
Meet MATRIX 55.
The pushbutton for
double-switches and
non-dimmable lightsources.
Meet MATRIX ZRB.
The battery driven
pushbutton that can
be placed anywhere.
Meet MATRIX ZBA.

Pushbutton Backlight

Get inspiration for usage of the backlight in the four pushbutton squares.

GUEST MODE

Ever had your guests confused about your smart home? Put your home in guest mode and light up selected squares in green. These are your guest switches.

GUEST MODE

Ever had your guests confused about your smart home? Put your home in guest mode and light up selected squares in green. These are your guest switches.

WARNING LIGHT

Let MATRIX light up in red if the stove or iron is on. Or if the smoke detector senses smoke at your grandma’s house.

WARNING LIGHT

Let MATRIX light up in red if the stove or iron is on. Or if the smoke detector senses smoke at your grandma’s house.

ORIENTATION

Use MATRIX as orientation light during the night, or as a night lamp for your kids.

ORIENTATION

Use MATRIX as orientation light during the night, or as a night lamp for your kids.

OPEN WINDOW

Never leave the house with open windows again! Together with a door/window sensor you can let the MATRIX at your doorway light up if a window in your house is still open.

OPEN WINDOW

Never leave the house with open windows again! Together with a door/window sensor you can let the MATRIX at your doorway light up if a window in your house is still open.

BECOME THE OMNISCIENT PARENT

Let MATRIX in the living room light up if the desk lamp, night lamp or stationary computer is on in the child’s room. But never let them know how you know!

BECOME THE OMNISCIENT PARENT

Let MATRIX in the living room light up if the desk lamp, night lamp or stationary computer is on in the child’s room. But never let them know how you know!

Customize your MATRIX

Make it easier for you, your spouse and your guests to navigate your Logic Home. With our Logic Symbol Customizer you can freely combine symbols from our library and your text to fit your MATRIX’ functions.

The symbols are laser engraved on the pushbuttons, thereby lasting for the lifetime of the product.

Choose your MATRIX variant:

MATRIX ZDB: Dimmer and Backlight

With its built-in universal light dimmer, backlit switches and wireless Z-Wave technology MATRIX ZDB really outsmarts your old wall switches.

The built-in light dimmer can control a local load, e.g. a lamp socket to replace a standard one-poled switch.

Use MATRIX ZDB where you want to dim your lights according to the time of the day and year. Choose bright lights for cooking and cleaning but softer lights in the evening, preparing you for bed.

  State-of-the-art light dimmer

The light dimmer can dim all dimmable light bulbs from 0-250 W. Even your low power LED bulbs.

repeater  Improves Z-Wave Network

Acts as a Z-Wave network repeater to increase reliability of the network.

  System compatibility

Matrix DB is designed to fit into all FUGA® compatible coverframes and boxes.

wifi  Z-Wave Plus

Based on the Z-Wave Plus 500 Series platform.

Construction

  1. A Cover Frame of your choice (1 module, not included).
  2. The Casing with all the magic inside.
  3. The Pushbutton is a translucent white plastic that matches your existing frames, socket outlets and wall switches.

 

Download “MATRIX ZDB5100 Datasheet” matrix-zdb5100-datasheet.pdf – Downloaded 130 times – 3 MB

 

EAN: 5714090000134

Mounting guide
Warning! Only authorised technicians under consideration of the country-specific installation norms may do works with 230 Volt mains power. Prior to the assembly of the product, the voltage network has to be switched off.

 

Wiring

Dimmed output (~), Neutral (N) and Line (L) must be connected according to the diagram below. Contacts with same markings (N or L) are internally connected and can be used for cable looping.


Cable Connection/Disconnection

Use a cable, max. 1,5 mm², with a stripped length of 9-10 mm. Solid cables are simply pushed into the connection terminals, whereas stranded cables must be connected by pressing a slotted screwdriver with 2,5 mm slot against release button while pushing in the cable (A). When disconnecting a cable use the release button as described above.

Demounting the Pushbutton Cover

To mount/unmount MATRIX the pushbutton cover must be removed. Loosen the cover with a slotted screwdriver; first insert it in the top (B) aftwerwards in the bottom (C).

Hold the top of the cover while the bottom is released.

Demounting from Cover Frame

MATRIX is demounted from a cover frame by inserting a slotted screwdriver in the two points (D) og (E).

Adding/Removing

Add/remove units in the Z-Wave network by pushing the center switch (I) with a non-conductive object. The LEDs of pushbutton 1 will now start blinking.

Restore Factory Settings

Factory settings are restored by pressing the center switch (I) and hold it for min. 10 seconds.

Technical Data
DIMENSIONS (HXWXD) 44 mm x 46 mm x 30 mm
POWER SUPPLY 100 – 240 V AC
POWER CONSUMPTION Max. 0.8 W / 0.5 W standby
LOAD 0-250 W
CLAMPS Screwless terminals 0.2 – 1.5 mm² / 20 – 14 AWG
CONTACTS 5 poles: 2 x looped line, 2 x looped neutral, 1 load
FUSE T2A (fixed)
RADIO PROTOCOL Z-Wave®: EU 868.4MHz – 500 Series
RADIO RANGE 40 m indoor / 80 m outdoor
PROTECTION RATING IP20
INCLUSION Classic Inclusion
ENCRYPTION S2 Security
APPROVALS CE
DS/EN 50491-3:2009 or DS/EN IEC 63044-3:2018
DS/EN 60669-2-1, DS/EN60669-2-1/A1, DS/EN 60669-2-1/A12, DS/EN 60669-2-1/AC:2007, DS/EN 60669-1:2018
Z-WAVE CERTIFICATION NO. ZC10-19066525

MATRIX ZRB: Double Relay and Backlight

MATRIX ZRB wall switch has two relay switches, multipurpose backlight and wireless Z-Wave communication with 4 scene controllers.

The two built-in relays can control local loads, e.g. lamp sockets, thereby replacing a standard two-poled switch.

Use MATRIX ZRB where you want control of two separate lights or where you cannot use a light dimmer. For instance with flourecent lights.

relay Relay switches

Can be used to control any two devices using max. 5 A or 1000 W in total for both relays.

repeater  Improves Z-Wave Network

Acts as a Z-Wave network repeater to increase reliability of the network.

  System compatibility

Matrix ZRB is designed to fit into all FUGA® compatible coverframes and boxes.

wifi  Z-Wave Plus

Based on the Z-Wave Plus 500 Series platform.

Construction

  1. A Cover Frame of your choice (1 module, not included).
  2. The Casing with all the magic inside.
  3. The Pushbutton is a translucent white plastic that matches your existing frames, socket outlets and wall switches.

 

EAN: 5714090000172

Mounting guide
Warning! Only authorised technicians under consideration of the country-specific installation norms may do works with 230 Volt mains power. Prior to the assembly of the product, the voltage network has to be switched off.

 

Wiring

Relay output (arrow), Neutral (N) and Line (L) must be connected according to the diagram below. Contacts with same markings (N or L) are internally connected and can be used for cable looping.


Cable Connection/Disconnection

Use a cable, max. 1,5 mm², with a stripped length of 9-10 mm. Solid cables are simply pushed into the connection terminals, whereas stranded cables must be connected by pressing a slotted screwdriver with 2,5 mm slot against release button while pushing in the cable (A). When disconnecting a cable use the release button as described above.

Demounting the Pushbutton Cover

To mount/unmount MATRIX the pushbutton cover must be removed. Loosen the cover with a slotted screwdriver; first insert it in the top (B) aftwerwards in the bottom (C).

Hold the top of the cover while the bottom is released.

Demounting from Cover Frame

MATRIX is demounted from a cover frame by inserting a slotted screwdriver in the two points (D) og (E).

Adding/Removing

Add/remove units in the Z-Wave network by pushing the center switch (I) with a non-conductive object. The LEDs of pushbutton 1 will now
start blinking.

Restore Factory Settings

Factory settings are restored by pressing the center switch (I) and hold it for min. 10 seconds.

Technical Data
DIMENSIONS (HXWXD) 44 mm x 46 mm x 30 mm
POWER SUPPLY 100 – 230 V AC
POWER CONSUMPTION Max. 0.8 W / 0.5 W standby
LOAD Max. 1000 W Total
CLAMPS Screwless terminals 0.2 – 1.5 mm² / 20 – 14 AWG
CONTACTS 5 poles: 2 x looped line, 2 x looped neutral, 1 load
FUSE T2A (fixed)
RADIO PROTOCOL Z-Wave®: EU 868.4MHz – 500 Series
RADIO RANGE 40 m indoor / 80 m outdoor
PROTECTION RATING IP20
INCLUSION Classic Inclusion
ENCRYPTION S2 Security

MATRIX ZBA: Z-Wave Battery Pushbutton

MATRIX ZBA is a wall switch that can control other Z-Wave devices with each of the four pushbuttons. MATRIX ZBA is completely wireless and can be placed everywhere with double sided tape or screws.

Use MATRIX ZBA in combination with DIMMY or MATRIX ZRB, MATRIX ZDB or other Z-Wave devices to control lights, curtains, relays etc.

Long Battery Life

The replaceable battery lasts up to 5 years.

  System compatibility

Matrix ZBA is designed to fit into all FUGA® compatible coverframes and boxes.

wifi  Z-Wave Plus

Based on the Z-Wave Plus 700 Series platform.

Construction

  1. A Cover frame of your choice (1 module, not included).
  2. The Battery is replaceable.
  3. The Casing with all the magic inside.
  4. The Pushbutton is a translucent white plastic that matches your existing frames, socket outlets and wall switches

 

EAN: 5714090000240

Mounting guide
Demounting the Pushbutton Cover

To mount/unmount MATRIX with screws the pushbutton cover must be removed. Loosen the cover with a slotted screwdriver; first insert it in the top (B) aftwerwards in the bottom (C).

Hold the top of the cover while the bottom is released.

If a technical mounting frame is used it is an advantage to remove the outer frame before demounting the pushbutton cover.

Demounting from Cover Frame

MATRIX is demounted from a cover frame by inserting a slotted screwdriver in the two points (D) og (E).

Adding/Removing

Add/remove units in the Z-Wave network by pushing the center switch (I) OR by triple-clicking the upper left pushbutton. The LEDs of pushbutton 1 will now
start blinking.

Restore Factory Settings

Factory settings are restored by pressing the center switch (I) and hold it for min. 10 seconds.

Technical Data
DIMENSIONS (HXWXD) 44 mm x 46 mm x 8 mm
POWER SUPPLY CR2032 Battery
BATTERY LIFE Up to 5 years
RADIO PROTOCOL Z-Wave®: EU 868.4MHz – 700 Series
RADIO RANGE Up to 100 m indoor / more than 200 m outdoor
PROTECTION RATING IP20
INCLUSION SmartStart Inclusion or Classic Inclusion
ENCRYPTION S2 Security

MATRIX 55: For the CE standard

With its built-in universal light dimmer, backlit switches and wireless Z-Wave technology MATRIX 55 really outsmarts your old wall switches.

The built-in light dimmer can control a local load, e.g. a lamp socket to replace a standard one-poled switch.

  State-of-the-art light dimmer

The light dimmer can dim all dimmable light bulbs from 0-250 W. Even your low power LED bulbs.

repeater  Improves Z-Wave Network

Acts as a Z-Wave network repeater to increase reliability of the network.

  System compatibility

The MATRIX 55 insert is constructed to fit into standard CE wall boxes (60 mm). The front is designed to fit into standard 55 mm cover frames including GIRA System 55, Elko Plus and Exxact.

wifi  Z-Wave Plus

Based on the Z-Wave Plus 500 Series platform.

Construction

  1. The Insert that contains all the magic and fits into CE standard wall boxes (60 mm).
  2. A Cover Frame of your choice (inner dimensions should be 55×55 mm) – not included.
  3. The Front Module has LED diodes and metal springs to fasten the front module to the insert.
  4. The Anti-theft Screw makes Matrix 55 suitable for public buildings and businesses.
  5. The Pushbutton is made from translucent white plastic that matches existing modules and cover frames on the market.

Download “MATRIX 55 ZDB5400 Datasheet” matrix-55-datasheet.pdf – Downloaded 93 times – 3 MB

 

EAN: 5714090000196

Mounting guide
Warning! Only authorised technicians under consideration of the country-specific installation norms may do works with 230 Volt mains power. Prior to the assembly of the product, the voltage network has to be switched off.

 

MATRIX 55 is designed for fitting into standard 60mm CE wall boxes. For compatible design frames, see section about design frames.

For easy installation MATRIX 55 is provided with a connection terminal with push-in terminations. The cable must have a stripped length between 9 and 10 mm. The maximum conductor size is 2.5 mm2, or maximum 1.5 mm2 for stranded conductors with a ferrule with plastic collar.

Wiring

Dimmed output (~), Neutral (N) and Line (L) must be connected according to the diagram below. Contacts with same markings (N or L) are internally connected and can be used for cable looping.

Cable connection / Disconnection

When installing a MATRIX 55, simply push solid cables into the connection terminals. Stranded cables must be connected by use of the release-buttons. Activate the release-button on the terminal with a slotted screwdriver with a 2.5 mm slot while pushing in the cable

When removing the cables, use the release-buttons as described above.

Fitting

Fit MATRIX using the elements in the figure below. The safety screw (4) is necessary in public buildings and businesses to avoid theft. Use bullets D) and F)-G) to mount the safety screw.

  1. Mount the Insert (1) in the wall box using the wiring diagram above, regard the UP arrow.
  2. Add the insert to the Z-Wave system, see Chapter 6.
  3. Place the design frame (2) over the insert (1).
  4. (Optional) Remove Pushbutton cover (5) from the front module.
  5. Plug the Pushbutton base (3) into the Insert (1), regard the UP arrow.
  6. (Optional) Fasten the Pushbutton base to the Insert with the Safety screw (4).
  7. (Optional) Snap on the Pushbutton cover (5).
Demounting the Pushbutton Cover when the Safety Screw is mounted

With the safety screw mounted, the pushbutton cover must be removed from the Pushbutton base before unscrewing. Use the following steps.

  1. Loosen the cover with a slotted screwdriver in one side in the slot between the cover and the cover frame;
    • First insert the screwdriver in the right top just below the upper snap (a) and pop out the snap.
    • Afterwards insert the screwdriver in the right bottom just above the lower snap (b). Now release the entire right side.
  2. Hold the right side out from the wall while the left side is released with a single pop somewhere on the left side (c).
  3. Now it is possible to unscrew the safety screw and remove the front module and insert from the wall box.

Adding/Removing

MATRIX 55 is a SmartStart enabled product and can be added into a Z-Wave network by scanning the Z-Wave QR Code present on the product with a controller providing SmartStart inclusion. No further action is required and the SmartStart product will be added automatically within 10 minutes of being switched on in the network vicinity.Find the DSK, QR code and PIN Code on the front of the insert module.

Add MATRIX 55 to a network with Classic Inclusion by pressing once on the switch (I) through the hole with a non-conductive object. The LED inside the module will start blinking.

Use same procedure for removing MATRIX 55 with Classic Exclusion.

If MATRIX 55 already belongs to a Z-Wave network, the remove process must be performed before adding it in a new network. Otherwise, the adding of the device will fail.

 

SmartStart Inclusion

 

Classic Inclusion

Restore Factory Settings

Factory settings are restored by pressing the switch through the hole (I) and hold it for min. 10 seconds.

Compatible Design Frames

MATRIX 55 is compatible with a range of design frames from other manufacturers. The design frame must have a 55×55 mm opening and a depth of min.10 mm. This includes, but is not limited to, the following frame systems:

  • Schneider Electric, Exxact
  • Elko Plus
  • GIRA, System 55
  • Merten, System M
  • Busch-Jaeger, Basic 55
Technical Data
DIMENSIONS (HXWXD) 70 (55) mm x 70 (55) mm x 39 (12) mm
POWER SUPPLY 100 – 230 V AC / 50 Hz
POWER CONSUMPTION Max. 0.8 W / 0.5 W standby
LOAD 0-250 W
CLAMPS Screwless terminals 0.25 – 2.5 mm² / 24 – 12 AWG
CONTACTS 5 poles, 2 x looped line, 2 x looped neutral, 1 x load
FUSE T2A (fixed)
RADIO PROTOCOL Z-Wave®: EU 868.4MHz – 500 Series
RADIO RANGE 40 m indoor / 80 m outdoor
PROTECTION RATING IP20
INCLUSION SmartStart Inclusion or Classic Inclusion
ENCRYPTION S2 Security
APPROVALS CE
DS/EN 50491-3:2009 or DS/EN IEC 63044-3:2018
DS/EN 60669-2-1, DS/EN60669-2-1/A1, DS/EN 60669-2-1/A12, DS/EN 60669-2-1/AC:2007, DS/EN 60669-1:2018
Z-WAVE CERTIFICATION NO. ZC10-19096765