COMING SOON

Add intelligence to your ceiling boxes

Connect to a group of lamps or connect to individual devices and control them from the Z-Wave network. DIMMY and RELLY easily fit into ceiling boxes, e.g .the Danish PL box. Dim everything from dimmable LEDs to incandescent light bulbs up to 250W with DIMMY and switch other types of lights and devices up to 1000W on/off with RELLY.

Z-WaveZ-Wave controlled lamp

Connect DIMMY or RELLY to a local load and control it with a Z-Wave wall switch such as MATRIX or through an app on a smartphone.

repeater  Improves Z-Wave Network

Acts as a Z-Wave network repeater to increase reliability of the network.

wifi  Z-Wave Plus

Based on the Z-Wave Plus 500 or 700 Series platform.

Compatibility

DIMMY and RELLY are designed to fit into PL ceiling boxes which are some of the smallest ceiling boxes in Europe. With a height of 13-15 mm, it leaves lots of space for cables in the ceiling box.

Metering

The meter reads the consumption of the connected device for you to keep an eye with your energy consumption.

wifi  Wireless Updates

Firmware can be updated through the Z-Wave network (OTA firmware updates).

DIMMY and RELLY can be mounted in a ceiling box or junction box.

Use cable relief. Optionally, use the screw holes to fasten to a surface.

Choose a variant:

ZDI5200: DIMMY

Use DIMMY where you want to dim your lights according to the time of the day and year. Choose bright lights for cooking and cleaning but softer lights in the evening, preparing you for bed.

  State-of-the-art light dimmer

The light dimmer can dim all dimmable light bulbs from 0-250 W. Even your low power LED bulbs.

wifi  Z-Wave Plus

Based on the Z-Wave Plus 500 Series platform.

DIMMY is very low with its 13-15 mm height.

 

EAN: 5714090000158

Technical Data
DIMENSIONS (HXWXD) 15 mm x 45 mm x 54 mm
POWER SUPPLY 100 – 230 V AC
POWER CONSUMPTION Max. 0.8 W / 0.5 W standby
LOAD 0-250 W
CLAMPS Screwless terminals 0.2 – 2.5 mm² / 24 – 14 AWG
CONTACTS 5 poles, 2 x looped line, 2 x looped neutral, 1 load
FUSE T2A (fixed)
RADIO PROTOCOL Z-Wave®: EU 868.4MHz – 500 Series
RADIO RANGE 40 m indoor / 80 m outdoor
PROTECTION RATING IP20
INLCUSION Classic Inclusion
ENCRYPTION S2 Security
APPROVALS CE
DS/EN 50491-3:2009 or DS/EN IEC 63044-3:2018
DS/EN 60669-2-1, DS/EN60669-2-1/A1, DS/EN 60669-2-1/A12, DS/EN 60669-2-1/AC:2007, DS/EN 60669-1:2018
Mounting guide
Warning! Only authorised technicians under consideration of the country-specific installation norms may do works with 230 Volt mains power. Prior to the assembly of the product, the voltage network has to be switched off.

 

Wiring

Dimmed output (↗), Neutral (N) and Line (L) must be connected according to the diagram below. Contacts with same markings (N or L) are internally connected and can be used for cable looping.

Figure A

 

Cable Connection/Disconnection

Use a cable, max. 2,5 mm², with a stripped length of 9-10 mm. The cable must be solid or closed with a ferrule. Connect the cable by simply pushing it into the connection terminal. Disconnect cables by pressing a slotted screwdriver with 2,5 mm slot against release button while pulling the cable (A)

Figure B

Adding/Removing

Add/remove DIMMY to the Z-Wave-network by pressing the center switch (I). The LED will now start blinking.


Figure C

Restore Factory Settings

Restore factory settings by pressing the center switch (I) for at least 10 seconds.

ZRE7240: RELLY

Use RELLY where you cannot use a light dimmer. For instance with groups of light sources exceeding what the dimmer can pull, or devices that must not be dimmed, for instance ventilation.

relay  Relay switch

Can be used to switch on/off any device up to 1000 W, e.g. a light source.

wifi  Z-Wave Plus

Based on the Z-Wave Plus 700 Series platform.

RELLY is very low with its 13-15 mm height.

 

EAN: 5714090000271

Technical Data
DIMENSIONS (HXWXD) 15 mm x 45 mm x 54 mm
POWER SUPPLY 100 – 230 V AC
POWER CONSUMPTION Max. 0.8 W / 0.5 W standby
LOAD max. 1000 W
CLAMPS Screwless terminals 0.2 – 2.5 mm² / 24 – 14 AWG
CONTACTS 5 poles, 2 x looped line, 2 x looped neutral, 1 load
FUSE T2A (fixed)
RADIO PROTOCOL Z-Wave®: EU 868.4MHz – 700 Series
RADIO RANGE Up to 100 m indoor / more than 200 m outdoor
PROTECTION RATING IP20
INLCUSION SmartStart Inclusion or Classic Inclusion
ENCRYPTION S2 Security
Mounting guide
Warning! Only authorised technicians under consideration of the country-specific installation norms may do works with 230 Volt mains power. Prior to the assembly of the product, the voltage network has to be switched off.

 

Wiring

Controlled output (↑), Neutral (N) and Line (L) must be connected according to the diagram below. Contacts with same markings (N or L) are internally connected and can be used for cable looping.

Figure A

 

Cable Connection/Disconnection

Use a cable, max. 2,5 mm², with a stripped length of 9-10 mm. The cable must be solid or closed with a ferrule. Connect the cable by simply pushing it into the connection terminal. Disconnect cables by pressing a slotted screwdriver with 2,5 mm slot against release button while pulling the cable (A)

Figure B

Adding/Removing

Add/remove RELLY to the Z-Wave-network by pressing the center switch (I). The LED will now start blinking.

 

Figure C

Restore Factory Settings

Restore factory settings by pressing the center switch (I) for at least 10 seconds.